National Fuel Gas Code Practice Test

These questions are part of the practice quiz. Start practicing

• Which fittings are appropriate for use when supplying fuel gas?
• What does BTU stand for?
• What defines a Journeyman Gasfitter?
• What is the maximum operating pressure of piping systems covered under NFPA 54?
• What section of NFPA 54 covers general appliance requirements?
• Which ASTM specification is referenced for steel, black, and hot dipped pipe?
• What is a necessary condition for the safe use of flexible connectors?
• What is the role of a vent connector in a fuel-gas system?
• What type of configurations may use a 3-way valve in gas systems?
• What is the maximum operating pressure for undiluted LP gas systems?
• What is the purpose of protecting piping in areas where hydrates or ice formation occurs?
• When new branches are installed to new appliances, which section is required to be pressure tested?
• Is NFPA 54 a safety code?
• In regard to the installation of underground gas piping, what dictates an increase in cover from 12 inches to 18 inches?
• What is necessary for piping that enters a building from underground?
• What does NFPA 54 say regarding modifications to existing gas piping systems?
• What type of fitting should be used when joining dissimilar metals underground?
• What is a required action for maintaining the safety of an operational gas piping system?
• What is a Hot Water Heating Boiler designed for?
• What must a conduit that is vented outdoors be able to prevent from entering?
• Which option describes a necessary condition for gas piping joints in corrosive environments?
• What is the minimum test duration for gas piping systems per 500 feet of pipe?
• What is the maximum distance allowed between supports for standard steel pipe installations?
• What type of tubing is referenced for copper brazed steel tubing?
• Which gas has the highest specific gravity?
• Which section addresses the installation of venting systems?
• What type of ventilation is required for gas appliances?
• When gas piping is used in industrial settings, how must it be mounted in solid floors?
• The test pressure for gas pipes should be no less than how many times the proposed maximum working pressure?
• What is the primary purpose of a gas heating system?
• Which section contains provisions for the inspection and testing of gas piping?
• What is a requirement for an appliance vent to be considered a system type?
• What is the travel of a piping offset that measures 12"?
• Which of the following correctly describes a gas appliance label?
• What role does pressure regulation play in natural gas systems?
• What mediums can be used for testing gas piping systems?
• What does it mean when equipment is described as "Listed"?
• Gas piping with fuel gas lighter than air, exceeding 5 psi, must be vented in which manner?
• The unthreaded portion of gas piping outlets must extend at least how many inches through finished walls?
• What is a Venting System primarily used for?
• What is required for underground piping installed beneath buildings?
• What is a mechanical exhaust system?
• What piping material is specified to be used for venting regulators?
• What is the installation limitation for plastic piping for fuel gas?
• Which organization is responsible for publishing the National Fuel Gas Code?
• Individual shutoff valves must be accessible from which location?
• What is necessary for the maintenance of gas appliances?
• Which type of pipe must be used underground before it enters a structure?
• What safety practice is recommended for the storage of LPG cylinders?
• What is the primary reason for sealing the space between gas piping and the building?
• In a gas system, how should the existing piping be assessed before adding appliances?
• What benefit does following manufacturer’s instructions provide during installation of gas appliances?
• In what year was the UA (Utility Association) founded?
• If a minimum of 12 inches of cover cannot be provided for underground piping, what must be done?
• What type of valve can be used to admit standby supply gas while shutting off the regular supply?
• Where should gas outlets not be located?
• What does the term "fuel gas" refer to in NFPA 54?
• What size should the branch outlet be in relation to the main supply line?
• What is the maximum allowable pressure for natural gas distribution in residential applications?
• Which type of coupling is prohibited in concealed gas piping?
• For a system in a single-family dwelling with a volume less than 10', how long should the test last?
• What gauge of tracer wire or tape should be buried with plastic pipe?
• What must be done to gas piping in contact with corrosive materials?
• Mechanical gauges measuring test pressures should have a scale that is not exceeding what factor of the test pressure?
• How far must a conduit installed underground extend outside the building?
• What is the primary requirement for gas piping materials according to NFPA 54?
• What is a requirement for exhaust vents on gas appliances?
• What kind of materials is not recommended for gas piping?
• UL stands for?
• What is a requirement when installing gas piping in corrosive environments?
• How are gas shutoff valves specified to be installed?
• What must be marked on a gas shutoff valve according to NFPA 54?
• Where can plastic pipe, tubing, and fittings used to supply fuel gas be utilized?
• When two gas pressure regulators are installed in series, what is required at the second regulator?
• What precaution should be taken for gas piping installed vertically in chases?
• How many grains of hydrogen sulfide can gas contain before copper and brass pipe should not be used?
• For what purpose should an emergency shutoff valve be installed?
• After repairs to the piping system following a pressure test, what needs to be tested?
• What is required of personnel installing gas piping according to NFPA 54?
• How should repair parts for gas appliances be selected?
• According to NFPA 54, what must be done to ensure the safe operation of gas appliances?
• What must be followed when installing a new gas appliance?
• What is the heating value of natural gas?
• Which of the following is a critical aspect of gas piping installation?
• What is the heating value of butane?
• In a common gas system serving multiple buildings, where should shutoff valves be installed?
• What does NFPA 54 state about the repairs of gas appliances?
• What is the minimum clearance required around gas appliances for maintenance access?
• Electrical circuits should not use what material as conductors?
• What is an important factor to consider regarding gas meters?
• When connecting pipes, what must be avoided to ensure accurate pressure testing?
• What is an acceptable method of verifying gas leaks in a piping system?
• MSS stands for?
• What would be the diameter squared times 0.785 times height of a 4' diameter, 5' long cylindrical tank?
• What factor should always be checked during the installation of gas appliances?
• What is the maximum allowable hydrogen sulfide level in gas for using copper and brass pipes?
• Where can plastic pipe be installed?
• What method is crucial for ensuring gas combustion efficiency?
• What is the standard for the installation of gas regulators?
• For which conditions should uncoated thread or socket welded joints not be used?
• What is the maximum design operating pressure for piping systems located inside buildings?
• What should be done if there are signs of corrosion on gas piping?
• Who is referred to as the Authority having Jurisdiction?
• What must be done if gas appliances emit unusual odors?
• What does the term "draft" refer to in gas systems?
• What safety feature is required to shut off the gas flow during an electrical current failure?
• What is a common consequence of inadequate venting in gas installations?
• What type of fittings should not be used where gas piping is concealed?
• What are the requirements for gas appliance location in relation to other objects?
• How should gas piping outlets facilitate the use of tools?
• What must be adhered to during the installation of gas piping systems?
• What is the specific gravity of butane?
• What is the specified pressure for natural gas systems as per NFPA 54?
• What must be done with appliances not included in a pressure test?
• How are appliance connections to gas supply lines required to be made?
• What material is recommended for piping if the vent installation is outdoors?
• What ensures that the gas shutoff valve is functioning correctly?
• What is the purpose of providing individual shutoff valves in tenant lines?
• Which pressure is exerted by a water column that is 100 feet high?
• How should venting occur for gas piping in vertical chases with fuel gas exceeding 5 psi?
• In what locations should aluminum alloy pipe not be used?
• What does the term "Approved" signify in the context of National Fuel Gas Code?
• What does the term "shall" imply in the context of regulations?
• Under what condition should a valve not be used in a piping system?
• For gas piping with fuel gas heavier than air, what is the venting requirement when installed in vertical chases?
• What is the minimum standard weight for steel and wrought iron steel required?
• What type of gas does the National Fuel Gas Code primarily address?
• Under what conditions can vent caps be used on gas appliances?
• What type of safety control must be used that will shut off the flow of gas in case of current failure?
• In which year did UA local 5 receive its charter?
• What is the purpose of venting in gas installations?
• What is the significance of isolating appliances during a pressure test?
• What is crucial when connecting the gas piping system to ensure safety?
• In industrial occupancies, gas pipe laid in solid floors must be installed in what manner?
• What is the minimum cover required for underground piping systems?
• What does the term “siphon loop” refer to in gas line installations?
• What is the proper action if a gas leak is detected?
• What should be the minimum test pressure applied for any gas piping system according to the standards?
• What is the specific gravity of natural gas?
• What standard specification must steel tubing comply with for gas lines?
• What is required for gas appliances according to the NFPA 54?
• What is the coverage extent of NFPA 54?
• What minimum thickness is required for a steel striker barrier installed between copper tubing and a finished wall?
• Which of the following applies to gas piping systems installations?
• What governs appliance fuel supply connections in gas installations?
• How is gas piping considered to be bonded?
• What is necessary to provide at any point in the line of pipe where condensate could collect?
• A drip shall not be located where the condensate is likely to do what?
• What is a critical condition that gas piping must meet before being covered?
• How frequently should gas appliances be inspected according to NFPA 54?
• Where should PVC vent piping not be installed?
• What is a "combustion air" requirement for gas appliances?
• Circulating Air is defined as what type of air?
• What is the specific gravity of propane?
• What must be done if an appliance is installed in a confined space?
• Gas outlets must be installed far enough from floors and walls to allow the use of what tool without strain?
• When adding appliances to a gas piping system, what must be checked?
• In NFPA 54, what is critical for the combustion process of gas appliances?
• What must be done prior to re-lighting a pilot light on a gas appliance?
• Which regulation pertains to the installation of gas-fired appliances?
• What must be provided in multiple tenant buildings with a master meter?
• What component must be used to close each outlet after installation?
• In gas installations, what is the acceptable method for supporting and securing gas piping?
• In non-industrial occupancies, how should gas pipe be encased in concrete?
• What is the minimum distance a gas vent must be from an opening into a building?
• Where should the open end of piping systems being purged not discharge?
• The suitable method for diverting gas discharge from the open end of piping is to avoid what?
• How should gas piping be marked when buried underground?
• What is one common cause of odors associated with gas appliances?
• What is necessary for proper gas system installation and operation?
• What documentation may be required for a gas installation inspection?
• What role does a Journeyman Gasfitter serve in a gas-related project?
• What is a requirement for the termination of venting systems for gas appliances?
• What should be the height of the unthreaded portion of a gas outlet above outdoor patios?
• What is the purpose of a line pressure regulator?
• What should be considered for the installation of appliances near potential hazards?
• ASTM stands for?
• Connections between metallic and plastic piping outdoors must use fittings that conform to which standards?
• What must plastic pipe, tubing, and fittings used to supply fuel gas be marked with?
• A column of water 100' high exerts how much pressure at its base?
• What should gas piping not be laid in contact with?
• How often should 3/4" or 1" steel pipe be supported?
• The unthreaded portion of gas piping outlets shall extend a minimum of how many inches above the surface of floors?
• What type of installations is NFPA 54 concerned with?
• What does NFPA 54 stipulate about the color of the gas piping in a system?
• What must be confirmed about gas piping before it is concealed in walls or floors?
• What does an increase in specific gravity indicate about a gas?
• How much should gas piping be sloped to prevent traps?
• Why is it important to understand the heating values of gases?
• What should be inspected before gas is introduced into new gas piping?
• Why is it important to provide adequate combustion air to gas appliances?
• What specification must regulator vent piping conform to?
• What guidelines does NFPA 54 give regarding gas appliance drain lines?
• Drip locations should be accessible to permit what actions?
• How should gas piping systems be routed through building structures?
• What is NFPA 70?
• How thick should concrete be when surrounding gas pipe embedded in portland cement floor slabs?
• For which purpose are vent caps designed according to code requirements?
• How is atmospheric pressure defined?
• How many millimeters are equivalent to one inch?
• Where should the gas piping systems not be interconnected when two or more meters are used?
• What does NFPA stand for?
• What is a dual-fuel appliance according to NFPA 54?
• What is the heating value of propane?
• A cylindrical tank with a diameter of 4' and a length of 5' contains how many cubic feet?
• How does the heating value of butane compare to that of propane?
• What does “equipment, materials or services included in a list” mean?
• How much does one gallon of water weigh approximately?
• Which method is used for detecting gas leaks according to National Fuel Gas Code?
• What is the primary purpose of the National Fuel Gas Code (NFPA 54)?
• ASME stands for what?
• What must be installed when a supplementary gas for standby use is connected downstream where a meter is not provided?
• What type of test is recommended after the installation of gas piping?
• Which of the following is NOT a precaution under the gas piping test regulations?
• What happens if the test pressure exceeds the maximum working pressure?
• What is specified in Section 24.5 of NFPA 54?
• Which term describes an organization responsible for enforcing code requirements?
• For gas systems serving multiple users, on which side should the gas piping systems remain separate?
• Underground piping, when installed through the outer foundation wall of a building, should be __________.
• What is the minimum opening requirement for chases used for gas regulator venting?
• What does the label on a gas appliance indicate?
• What is Dilution Air?
• What is the title of the publication MSS SP-58?
• What is the required minimum diameter for a gas vent for residential use?
• What is the function of a condensate trap in gas venting systems?
• What is indicated by the term "Circulating Air" in HVAC systems?
• What does the term "purge" refer to in gas systems?
• Where is a drip required to be provided as specified by the AHJ or serving gas supplier?
• What specific document or code must be consulted for fuel gas appliance certification?
• What is the purpose of a venting system?
• What action must be taken immediately after installing a gas outlet?
• In NFPA 54, which section discusses the installation of gas piping?
• Where should gas piping with fuel gas lighter than air, exceeding 5 psi, be vented when installed in vertical chases?
• What is the significance of a gas appliance label?
• How often should gas appliances be inspected according to NFPA 54?
• When can plastic piping terminate above grade?
• What does "Heating Value" signify?
• What is the purpose of testing gas piping systems?